Here’s another post for Jane.

The bezel….continued.

I wrote this at the weekend and wanted to finish the piece before I posted it.

I shouldn’t have bothered as it all went bottom’s up from there.

I will show you the first bit, however.

Especially for Jane.

This stone was too tall for my thin bezel wire, and too short for the super duper thick bezel wire.

Tiffany Stone

Tiffany Stone

As I only have the two widths of wire in my supply kit, I chose the thick wire.

Which, as it turns out, is perfect for my notes to Jane.

Solder the bezel wire together on one of the flat sides of the stone. See – HERE for soldering tips. It’s not a good idea to solder at a corner or point. I like the join to be in a place that can be hidden by some of my design.


At this point although the bezel is cut to fit the stone it’s probably been distorted slightly during soldering. I like to run my flat nose pliers, or burnishing tool, around the edges to really make sure it all fits snug to the stone. I also take my flat nose pliers to define the sharper corners by folding a line at the tip edge of the stone.

This gives it a nice, crisp, finished look.

The bottom shape of the bezel wire is the most important as this is the part which will be soldered to the sheet metal. If the bottom of the wire is not exactly the shape of the stone it will look bad and the stone won’t fit correctly in the collar again.

As you’re pushing the wire to the stone (see below) you can distort the top edge of the wire by unintentionally curving it over the top of the stone. Although, in a pinch, you can straighten the sides of the bezel once you’ve soldered it to the back plate this is not the best approach. I take the stone out of the bezel wire through the bottom of the collar, and replace it in the collar from the top to ensure that the stone fits nicely into the bezel from the top once I’ve soldered it.

I do this several times until I’m satisfied that the stone passes smoothly from the top through the bottom.


When you have done this and sanded both the bottom of the collar and the surface you’re to solder it onto make sure one more time that the stone fits before you solder.

I suppose you could do the sanding first


I guess I’m stuck in my ways.

It seems a lot of checking, but once you get the hang of it you don’t need to do it as much.

Once I’ve soldered the collar to the backing plate I like to drill a hole in the bottom so that I can get the stone out again.

I do this because I usually have a design on the back of the pendant and you don’t see the hole afterward. You can run dental floss across the bottom of the stone if you don’t want to drill a hole. This gets it out fine also.

The main thing is that it’s important to be able to get your stone out again as you trim your collar.


Now put the stone back into it’s setting.

I’ve got a wonky stone here which I hadn’t noticed before.



Ignore that and run your pencil around the top of the stone and mark the inside of the collar.

Be careful not to mark the stone. Pencil will generally come off, but I wouldn’t want to get Sharpie on it for instance.


Take the stone out of the setting.

(See. Really wonky.)


I used my snippers to cut away most of the unwanted wire.

Usually this isn’t necessary unless you have odd stones that don’t fit the regular widths of wire, or you don’t have it on hand. You can make your own bezel wire from sheet metal, but I like the pre cut wire.

Lot less fuss.

I snipped here because it would have taken too long to file down and I would have gone out of my mind with boredom.


Sometimes it can be a bit tricky, just snip gently.


Then fit the stone back in again to see if you need to snip more.


At this point use a file or sanding disc on your Dremel or Fordom to file away the rest of the bezel wire down to the pencil line.

You might just be able to see in the photo below that I have marked a dip in the pointed corner with a pen, and less visibly, a slight dip at the curved corners.


By sanding these points away slightly when you push the bezel wire over the edge of the stone it will look cleaner.


I graduate the curve into the corners.

(Sorry about the grubby hands. I fired my hand model last week and haven’t found a replacement yet who’s also willing to make the tea.)


O.k. So.

That’s when I had to go in to make dinner.

(Note. You should never turn your back on a piece that is all going according to plan. You may never get back the magic.)

The next day all hell broke loose.

Oh yes it started out rosy.

I made the piece a nice dangly thing with a small set stone.

(I was going to show you how to set the tiny stone Jane, but thought that might put you over the edge and so decided to save it for later.)

I fashioned a lovely design for the back, and a bale for the chain.

Then, in the blink of an eye when my concentration turned to which song I should sing at my X Factor audition – Nina Simone, or Billie Holiday – I soldered the bezel right off that backing plate, and had to swear a little (only in my head mind) when it melted away down one side.

Time of death was around three o’clock central time.

Not one to give in I made it another collar which, because I was ticked off, never did quite fit the stone as well as the first one.

I think I was trying to punish the stone at this point but rather bit off my nose to save my face.

As I had already filed down the plate after I’d soldered the first collar I had to be extra careful fitting the second one to the back. I could’ve made it all new, but I’d already put my design on the back and darn it if it was going to beat me.

As a consequence, will all my fiddling, the corner of the #$$^&*#! stone broke off and fell onto the floor where I decided to leave it until I was in a better frame of mind.

At this point the atmosphere in the studio was a bit tense, to say the lease, and Willow had to hide.


Bless her.

Actually Willow always hides there even when I’m singing.

O.K. probably because I’m singing.

I hope that’s not why she’s gone deaf…

All said and done, however, I think Jane that you might be able to get something out of this mess to help with the first stage of bezel setting.

I’ll try to collect myself enough to make a complete one next time.



 Too depressing?

I wouldn’t want Simon to roll his eyes.

My only other choice is the lonely goatherd.


Only Willow physically shakes when I yodel so I have to use hand signals on that bit.

I think I’ll stick with Nina.


About coldfeetstudio

I am English, but live in Houston, TX. I have a degree in Sculpture. I love to make art. I sell my art for charity as I believe there should be no reason for someone to go hungry in this world. I am a wife, mother, pottery maker, jewelry maker, quilt maker, painter, cat lover, and, dog liker. And I am very fortunate to be all these things. View all posts by coldfeetstudio

11 responses to “Here’s another post for Jane.

  • wiredweirdly

    Great post!!! Thanks for sharing so many tips – very timely and helpful!

    • coldfeetstudio

      Well I don’t think you really needed any tips. Your ‘first’ bezeled ring is fabulous! Btw, you’re on my shout out page, unless you prefer to be taken off it ;)

      • wiredweirdly

        Sometimes when you don’t know all of the rules when attempting something new, you can do things wrong and still have it turn out right. That ring success was quickly followed with several failures. It’s a learning process, and there’s nothing wrong with that! There were a couple of things in this post that will definitely be helpful for future projects.
        Thank you for the shout out!!! Much appreciated!
        So, the other thing this post reminded me of was a hunk o’ Labradorite a customer sent to me to work. I rarely blog, but this one deserved some… venting. You can read about it here, if you’d like!

      • coldfeetstudio

        Fun post Angie. How much do you charge for something like that? That’s a lot of work.

      • wiredweirdly

        Thank you! :) I did NOT charge her enough. I think it was $150. It was a huge time suck and added a mountain to my recycle pile.

  • Paula

    There is nothing worse than a bezel melt down–so frustrating! It happened to me a few weeks ago with an earring setting. I’d love to get a Tiffany stone–love the pear shape of the one you were working with. It’s so nice of you to share your steps–I can learn something new or be relieved that I’m doing something the same way!

  • Jane Winningham

    thanks Deborah ,you are so helpful to me so i just file down the corners,i will have to try again then :) thank you

  • pennystreasures

    Sorry to hear about the meltdown. It’s always so frustrating when little metal pieces aren’t cooperating!

    In a previous post you mentioned the filigree artist at that show in the Heights. I did in fact see her work as I was strolling around to check out the other booths. And I had picked up her card but now I don’t know what I’ve done with it. But her work was stunning! There was a pair of triangle shaped earrings that were sooo awesome.

    Are you really going to audition for X Factor? I like the goatherd song!

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: